三年成全免费高清观看电视剧完整版,激情都市,美国式1982版保罗

當前位置：首頁 - 新聞動態 > 行業資訊

行業資訊

行業資訊公司新聞

行業資訊

聯系我們

濟南福華建材廠

聯系人：吳老師　

電話：　

手機：13864111871
0531-81901300
地址：山東省濟南市高新開發區巨野河辦事處山圈村西

膩子粉怎么施工才能達到更好效果

來源：http://www.wavc.cn 日期：2023-06-28 發布人：

刮膩子是裝修的必要程序，可以使墻面基層高低不平的地方變得平整光滑，還能有效避免外界的水汽腐蝕墻壁，是基層處理中重要的步驟，今天我們就來說說濟南膩子粉怎么施工，批刮膩子時需要注意些什么。

Puttying is a necessary procedure for decoration, which can make uneven areas on the wall surface smooth and prevent external moisture from corroding the wall. It is an important step in the treatment of the base layer. Today, we will talk about how to apply Jinan putty powder and what to pay attention to when applying putty in batches.

1、刮膩子施工前需進行測量

1. Measurement is required before applying putty

刮膩子施工前，需要先用尺子來進行測量，看看墻面是否水平，以便于確定刮膩子的方式。刮膩子一般施工兩遍即可，不僅讓墻面更加平整，而且能將底色覆蓋掉。如果墻面不平整的地方，則涂刮多遍膩子來進行找平處理，但每道膩子施工間隔應在兩三小時，確保墻面充分干燥。

Before applying putty, it is necessary to measure with a ruler to see if the wall is level, in order to determine the method of applying putty. Puttying is usually done twice, which not only makes the wall smoother but also covers the base color. If the wall is uneven, apply multiple layers of putty for leveling treatment, but the interval between each layer of putty construction should be two to three hours to ensure that the wall is fully dry.

2、膩子粉施工需做基層處理

2. Putty powder construction requires base treatment

檢查基面及基層清理，包括清除墻面砂灰結塊、浮砂及塵土，以提高膩子粉的施工面基層的平整度和附著力，確保基面無污染，無空鼓，無縫隙，無疏松無掉粉現象。

Check the cleaning of the base surface and base layer, including removing sand and ash lumps, floating sand, and dust from the wall surface, to improve the smoothness and adhesion of the putty powder construction surface base layer, and ensure that the base surface is free from pollution, hollowing, gaps, looseness, and powder loss.

3、施工溫度要在5℃以上

3. The construction temperature should be above 5 ℃

施工環境一直都是非常重要的因素，如果環境溫度過低，容易影響到膩子中有機添加劑的溶解，如果添加劑不能充分溶解，或是溶解速度過慢，將影響膩子批刮后的成膜質量和施工性能。施工環境過熱、過干也不行，膩子施工適宜在5℃-35℃的環境下進行。

The construction environment has always been a very important factor. If the environmental temperature is too low, it can easily affect the dissolution of organic additives in the putty. If the additives cannot be fully dissolved or the dissolution rate is too slow, it will affect the film forming quality and construction performance of the putty after scraping. The construction environment is too hot or too dry, and putty construction is suitable to be carried out in an environment of 5 ℃ -35 ℃.
濟南膩子粉

4、膩子批刮厚度在0.5mm-1mm之間

4. The thickness of putty batch scraping is between 0.5mm-1mm

膩子的批刮不能太薄也不能太厚。太薄的話，膩子層容易失水過快導致膩子出現粉化，終會影響涂裝的效果。而膩子層批刮得越厚，則其干縮強度越大，越容易開裂。因此，單次膩子的批刮厚度好是在0.5mm-1mm之間。

The putty batch should not be too thin or too thick. If it is too thin, the putty layer may lose water too quickly, leading to powdering of the putty and ultimately affecting the coating effect. The thicker the putty layer is scraped, the greater its dry shrinkage strength and the easier it is to crack. Therefore, the optimal thickness for a single batch of putty is between 0.5mm-1mm.

5、膩子攪拌好放置幾分鐘，再攪拌使用

5. Mix the putty and let it stand for a few minutes before mixing and using it

在攪拌后放置一會兒，是為了給膩子中的成分提供充分溶解的時間以保證膩子的施工性能和后期成膜質量，避免造成添加劑的浪費。膩子在調制成膏狀后，好在半小時內使用，以免膩子變質影響施工效果。

After mixing, it is left for a while to provide sufficient dissolution time for the components in the putty to ensure its construction performance and later film quality, and to avoid waste of additives. After the putty is prepared into a paste, it is recommended to use it within half an hour to prevent the putty from deteriorating and affecting the construction effect.

6、底層膩子未干透不得做面層

6. The bottom layer of putty shall not be dried thoroughly and the surface layer shall not be made

內墻膩子粉膩子層不宜過厚，一定要等干透方可批第二遍膩子。冬季施工，注意防凍通風干燥，底層膩子未干透不得做面層。

The inner wall putty powder putty layer should not be too thick. It is necessary to wait for it to dry thoroughly before applying the second layer of putty. During winter construction, pay attention to antifreeze, ventilation, and dryness. If the bottom putty is not fully dry, the surface layer cannot be made.

7、刮膩子，這些部位要貼布處理

7. Apply putty and apply cloth to these areas for treatment

如果使用普通膩子，或耐水膩子，則輕體墻、隔墻板之間接縫處、家具和墻面接縫處、墻面開槽處等部位好采用貼布處理工藝。如果使用彈性膩子，就可以不用貼布處理，直接批刮即可。

If ordinary putty or water resistant putty is used, the bonding treatment process should be used for the joints between lightweight walls, partition boards, furniture and wall joints, and wall grooves. If elastic putty is used, it can be directly scraped without applying a cloth.

批刮膩子不僅可以讓墻面更美觀，延長墻壁的壽命，還可以協助房間的防潮，注意以上事項，才能讓發揮膩子的作用，讓房屋得到真正的保護。更多相關事項就來我們網站http://www.wavc.cn咨詢！

Applying putty in batches can not only make the walls more beautiful and extend their lifespan, but also assist in preventing moisture in the room. Pay attention to the above matters in order to fully utilize the function of putty and truly protect the house. For more related matters, come to our website http://www.wavc.cn consulting service

上一篇：保溫砂漿空鼓脫落是什么原因造成的？
下一篇：抹面砂漿易出現的3大質量問題及解決措施

相關推薦：

???

聯系方式：