抹面（抗裂）砂漿

　　Plastering (crack resistant) mortar

　　《模塑聚苯板薄抹灰外墻外保溫系統材料》GB/T 29906 、《膠粉聚苯顆粒外墻外保溫系統材料》JG/T 158

　　GB/T 29906 "Materials for Thin Plastered Exterior Wall Insulation System of Molded Polystyrene Board" and JG/T 158 "Materials for Exterior Wall Insulation System of Rubber Powder Polystyrene Particles"

　　依據《建筑節能工程施工質量驗收標準》GB 50411，復試項目：拉伸粘結強度壓折比。組批原則及送檢規定：同廠家、同品種產品，按照扣除門窗洞口后的保溫墻面面積所使 用的材料量，在 5000m2 以內時復驗一次；面積每增加 5000m2 時應增加一次。同工程項目、同施工單位且同期施工的多個單位工程，可合并計算抽檢面積。當獲得建筑節能產品認證、具有節能標識或連續三次見證取樣檢驗均一次檢驗合格時，其檢驗批的容量可以擴大一倍，其每 5000m2為一個檢驗批，檢驗批的容量擴大一倍，即 5000m2變 10000m2，復驗一次；

　　According to the "Construction Quality Acceptance Standard for Building Energy Efficiency Engineering" GB 50411, the retest item is the tensile bonding strength and compression ratio. Batch principle and inspection regulations: For products of the same manufacturer and variety, a retest shall be conducted within 5000m2 based on the amount of material used for the insulation wall area after deducting door and window openings; When the area increases by 5000m2, it should be increased once. Multiple unit projects with the same engineering project, construction unit, and simultaneous construction can be combined to calculate the sampling area. When obtaining certification for building energy-saving products, having energy-saving labels, or passing three consecutive witness sampling inspections, the capacity of the inspection batch can be doubled. Each 5000m2 is an inspection batch, and the capacity of the inspection batch is doubled, that is, 5000m2 becomes 10000m2 and needs to be retested once;

　　7kg 干混合料

　　7kg dry mixture

　　依據《硬泡聚氨酯保溫防水工程技術規范》GB 50404，復試項目：原強度拉伸粘結強度、耐水拉伸粘結強度。組批原則及送檢規定：每 500m2～1000m2 劃分為一個檢驗批，不足 500m2 也應劃分為一個檢驗批；每個檢驗批每 100m2 應至少抽查一處，每處不得小于10m2；

　　According to the Technical Specification for Hard Foam Polyurethane Insulation and Waterproofing Engineering GB 50404, the retest items are: original strength tensile bonding strength, water-resistant tensile bonding strength. Batch principle and inspection regulations: Every 500m2 to 1000m2 should be divided into an inspection batch, and any area less than 500m2 should also be divided into an inspection batch; Each inspection batch should have at least one spot checked every 100m2, and each spot should not be less than 10m2;

　　7kg 干混合料

　　7kg dry mixture

　　依據《外墻外保溫工程技術標準》JGJ 144，復試項目：干燥狀態和浸水48h 拉伸粘結強度 （與 EPS板或膠粉 EPS 顆粒保溫漿料 和水泥砂漿）。組批原則及送檢規定：同廠家、同品種產品，按照扣除門窗洞口后的保溫墻面面積所使用的材料量，在 5000m2 以內時復驗一次；面積每增加 5000m2 時應增加一次。同工程項目、同施工單位且同期施工的多個單位工程，可合并計算抽檢面積。當獲得建筑節能產品認證、具有節能標識或連續三次見證取樣檢驗均一次檢驗合格時，其檢驗批的容量可以擴大一倍，其每 5000m2為一個檢驗批，檢驗批的容量擴大一倍，即 5000m2變 10000m2，復驗一次；7kg 干混合料。需隨砂漿配送與施工現場配套的保溫材料 0.8m2

　　According to the Technical Standard for External Wall Insulation Engineering JGJ 144, the retest item is the tensile bond strength (with EPS board or rubber powder EPS particle insulation slurry and cement mortar) in dry state and immersed in water for 48 hours. Batch principle and inspection regulations: For products of the same manufacturer and variety, a retest shall be conducted within 5000m2 based on the amount of material used for the insulation wall area after deducting door and window openings; When the area increases by 5000m2, it should be increased once. Multiple unit projects with the same engineering project, construction unit, and simultaneous construction can be combined to calculate the sampling area. When obtaining certification for building energy-saving products, having energy-saving labels, or passing three consecutive witness sampling inspections, the capacity of the inspection batch can be doubled. Each 5000m2 is an inspection batch, and the capacity of the inspection batch is doubled, that is, 5000m2 becomes 10000m2 and needs to be retested once; 7kg dry mixture. 0.8m2 insulation material to be delivered with mortar and matched with the construction site

　　依據《建筑外墻外保溫防火隔離帶技術規程》JGJ 289，復試項目：原強度和耐水拉伸粘結強度（與防火隔離帶保溫板）。組批原則及送檢規定：同一廠家同一品種的產品，當單位工程建筑面積在 20000 m2以下時，各抽查不少于 3 次；當 20000 m2以上時各抽查不少于 6 次；7kg 干混合料。需隨砂漿配送與施工現場配套的保溫材料 0.8m2

　　According to the Technical Specification for External Thermal Insulation and Fire Insulation of Building Exterior Walls JGJ 289, the retest items are: original strength and water-resistant tensile bonding strength (with fire insulation board). Batch principle and inspection regulations: For products of the same manufacturer and variety, when the unit construction area is less than 20000 m2, each inspection shall be conducted no less than 3 times; When the area is over 20000 square meters, each spot check shall be conducted no less than 6 times; 7kg dry mixture. 0.8m2 insulation material to be delivered with mortar and matched with the construction site

　　依據《外墻內保溫工程技術標準》JGJ/T 261，復試項目：拉伸粘結強度。組批原則及送檢規定：同廠家、同品種產品，按照扣除門窗洞口后的保溫墻面面積所使用的材料量，在 5000m2 以內時復驗一次；面積每增加 5000m2 時應增加一次。同工程項目、同施工單位且同期施工的多個單位工程，可合并計算抽檢面積。當獲得建筑節能產品認證、具有節能標識或連續三次見證取樣檢驗均一次檢驗合格時，其檢驗批的容量可以擴大一倍，其每 5000m2為一個檢驗批，檢驗批的容量擴大一倍，即 5000m2變 10000m2，復驗一次；7kg 干混合料

　　According to the Technical Standard for External Wall and Internal Insulation Engineering JGJ/T 261, the retest item is tensile bonding strength. Batch principle and inspection regulations: For products of the same manufacturer and variety, a retest shall be conducted within 5000m2 based on the amount of material used for the insulation wall area after deducting door and window openings; When the area increases by 5000m2, it should be increased once. Multiple unit projects with the same engineering project, construction unit, and simultaneous construction can be combined to calculate the sampling area. When obtaining certification for building energy-saving products, having energy-saving labels, or passing three consecutive witness sampling inspections, the capacity of the inspection batch can be doubled. Each 5000m2 is an inspection batch, and the capacity of the inspection batch is doubled, that is, 5000m2 becomes 10000m2 and needs to be retested once; 7kg dry mixture

　　本文由 濟南抹面砂漿   友情奉獻.更多有關的知識請點擊  http://www.wavc.cn/   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan plaster mortar For more related knowledge, please click http://www.wavc.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.